
Solved: FT232h as synchronoud FIFO - Intel Community
Sep 16, 2020 · To use the asynchronous FIFO transfer mode available on FT2232H, its hardware and driver must be configured as 245 FIFO and D2XX respectively. In this article, Channel A of FT2232H is configured as FIFO, which provides the following signals:
FT2232H as USB blaster and RS232 - Intel Community
May 2, 2010 · I'm trying to use the FT2232 instead of the standard USB Blaster, AND as a USB to RS232 bridge. according to device data sheet it can work as bridge from USB to JTAG and RS232. what is not explained in the documentation is how to make it work with the Quartus. FTDI supply a DLL file to make the USB to JTAG bridge, but I probably need some "glue" between the Quartus and this DLL. I hope I made ...
FT2232H 245 Synchronous FIFO Mode problem - Intel Community
Jan 21, 2014 · Hello Im very new to FPGA's and am still learning so please be kind if the problem is obvious :) i have a FT2232H set to 245 Synchronous FIFO Mode. i have a program on the pc using the d2xx drivers sending exactly 512 bytes. the problem is when the fpga receives these 512 bytes and p...
Re: FTDI FT2232H Sync FIFO + FPGA - Intel Community
Sep 11, 2024 · I'm using Morph-IC II and i'm having problems establishing the usb-communication between my Cyclone 2 and the FTDI FT2232H. My objective is to send a start/reset signal from PC->FPGA, then access the data from the FPGA till an end/reset signal.
Using FTDI FT2232H to load Cyclone 3 - Intel Community
Aug 2, 2012 · Hi I have a hard time finding supporting documentation on the FTDI site regarding using a FTDI FT2232H device, one port is used for Data transfer ( 40 M) and the other is only used to program the FPGA (Active Serial) (and monitoring nConfig, nStatus, Config_Done). I am going to load the "name....
FT2232H in Sync FIFO Mode - TXE# stuck high - Intel Community
Aug 4, 2016 · I have a Moprh-IC-II board and I'm trying to communicate via USB with a FT2232H in Sync FIFO Mode and D2XX Drivers. I manage to have the 60MHz clock input (my main fpga clock) from the ft2232h, and i can transfer data from the PC to my fpga via ft2232h with FT_Write (). FIFO Mode seems to work as expected on this side. The RXF# signal is working, going low when needed (I'm checking signals ...
Some issue on FT2232H in Synchronous FIFO - Intel Community
Jan 13, 2016 · Hello everyone! I have some troubles with the FTDI chip. I use it in this way: FPGA+FT2232H on custom board and PC Application on the other side. All stuff using in Synchronous FIFO mode. So from now I’m trying to send a byte command from FPGA and catch it in the windows application. And here is ...
Re: FT2232H as USB blaster and RS232 - Intel Community
May 2, 2010 · I'm trying to use the FT2232 instead of the standard USB Blaster, AND as a USB to RS232 bridge. according to device data sheet it can work as bridge from USB to JTAG and RS232. what is not explained in the documentation is how to make it work with the Quartus. FTDI supply a DLL file to make the U...
using a FT2232H to load a Cyclone 3 - Intel Community
Jan 15, 2010 · Yes, PS is usually the best method to load the FPGA configuration by a processor. FT2232H in MPSSE mode should be able to perform at it's maximum speed of 30 MHz when operated at at a high speed USB port.
解決済み: Re: FT232h as synchronoud FIFO - Intel Community
Sep 24, 2020 · To use the asynchronous FIFO transfer mode available on FT2232H, its hardware and driver must be configured as 245 FIFO and D2XX respectively. In this article, Channel A of FT2232H is configured as FIFO, which provides the following signals: